Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
Everyone is bound to have their personal piece of advice when it comes to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging project. If the old bathtub is easily available, the project can relocate rapidly; if you have to open a wall to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to move out the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the work and are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This article will assist you install a brand-new bathtub in your washroom if you have already acquired a brand-new tub as well as do not require to alter the plan of your previous water supply pipes.
Your tools as well as product list need to consist of the following:
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water remaining in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Prior to going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, put the bathtub in the needed position. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bathtub up until the level reads level.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water and also examine all joints and also brand-new pipework for leaks as well as tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the bathtub must wait until the tub has been made use of at the very least once as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark below. We would be interested to see your suggestions about this write up. We hope that you visit us again in the near future. Loved our posting? Please share it. Help others find it. Thanks so much for going through it.
Secure your space, call! Report this page